​​

Strokes per minute (X-/Y-axis): 950 strokes for 2-mm ram strokes at 2-mm pitch (X-axis) 330/270 strokes for 3-mm ram strokes at 25.4-mm pitch 290/240 strokes for 8-mm ram strokes at 25.4-mm pitch 

 

Maximum ram stroke length: 40 mm {1.575"} Maximum worksheet thickness: 3.5 mm {0.138"} (Mild steel) 

Maximum worksheet size: (X × Y) 5000 × 1525 mm {196.850 × 60.039"} Punching accuracy: ±0.1 mm {0.004"} 

Maximum worksheet mass (weight): 150 kg {330 lb.} at axis feed-speed F4 75 kg {165 lb.} at axis feed-speed F1 Least input increment: 0.01 mm {0.001"}, 0.01º 

Maximum carriage (X-axis) feed speed: 80 m/min {262 ft/min} 

Maximum table (Y-axis) feed speed: 80 m/min {262 ft/min} 

Maximum turret rotational speed: 30 min -1 {30 rpm} 

 

Hydraulic pump motor: 15 kW {20.11 HP}, 4P Required electric power: 40 kVA 

Compressed air pressure: 0.49 MPa {5.0 kgf/cm 2 or 72 psi} 

Hydraulic unit cooling capacity: 20.9 kW {18000 kcal/h} 

Machine mass (weight): 19 metric tons {20.9 U.S. tons} 

 

L-shear: 

 

Cutting capacity: 157 kN {16 metric tons} 

Ram driving method: AC servo motor 

Ram stroke method: Guillotine type 

Maximum worksheet thickness: 3.5mm {0.138"} (Mild steel) 

Stroke speed: 120 min -1 {120 spm} 

Feed-cut (25.4mm pitch): 75 min -1 {75 cpm} 

Cutting length (blade length): X-/Y-axis 800/1250 mm {31.496/49.213"} 

X-axis maximum progressive cutting length: 500 mm {19.686"} 

Shear angle: 1 deg. 

Machine mass (weight): 18 metric tons {19.8 U.S. tons} 

 

CNC unit: 

 

CNC unit model Fanuc Series 18i-PA + PHNC Number of controlled axes 4 axes (X, Y, T, C) + 1 axis (PHNC) Program code ISO/EIA Programming method Combination of absolute and incremental systems Least input increment 0.01 mm {0.001"}, 0.01° Memory capacity Maximum of 64000 characters or maximum tape length of about 160 m {520 ft} Temperature: 0 to 40°C {32 to 104°F} 

 

Operating PHNC unit: Model S-PHNC Number of controlled axes 1 (press) Least input increment 0.01 mm {0.001"} Number of processing patterns: 2 for punching 1 for nibbling 250 for forming 10 for knockout 10 for marking 4 for slitting 

Self-diagnostic function: Yes 

Built-in clock: Yes

Preparatory functions: 

1) Punching speed learning function 

2) Function of changing punching speed with time zone 

3) Function of changing ram up position 

4) Upper limit compensating function 

5) Warming-up function 

 

 

 

Specifications for the Auto Storage and the Sorter: The specifications for the Auto Storage, the two parts of the system that support the Turret Punch Press, are as follows: Auto Storage 651H (AS-651H) Ceiling Height 14.22 feet Number of Shelves 6 shelves Material Type Ferrous and Non-ferrous 

Materia l Thickness Range Mild Steel (0.024 - 0.135) Maximum Shelf Load 4400 Lbs. per shelf 

Maximum Material Stacking Height 10.24 inches (including 4" pallet) 

Maximum Material Sheet Size 120.0 x 60 .0 inches Minimum Material Sheet Size 30.0 x 12.0 inches (Size may vary depending on NC machine) 

Loader Speed 4000 inches per minute 

Loader Pipe Roller Speed 2362 inches per minute Traverser Speed 260 inches per minute Vacuum Lifter Configuration 3.15 inches, diameter times 8 pads Sheet Separation Vibrator 3.15 inches, diameter times 8 pads 

Minimum Electric Required 5kVA 230/480V 60Hz Dry Air Required 81 PSI 42 CFM Sorter (SOC1516) Maximum Part Size 120.0 x 60.0 inches Minimum Part Size 2.0 x 2.0 inches Sorting Destinations 3 (Small parts, big parts, and scrap) 

Material Specifications: The following is a list of the material specifications that the Punching Cell is capable of processing: Mild steel, Galvanized steel, Stainless steel, Aluminum (Ferrous and Non-ferrous) Material Thickness: Mild steel: 0.024" - 0.135" (24 GA - 10 GA)

Galvanized steel: 0.024" - 0.135" (24 GA - 10 GA) Aluminum: 0.024" - 0.135" (24 GA - 10 GA) 

Stainless steel: 0.024" - 0.080" (24 GA - 14 GA)